SAE J211 FREE DOWNLOAD

Tags Add Tags filter design filtering signal processing. The padded data set is then passed through the filter equation and then the extra points at the ends are thrown out. The signal-to-noise ratio of the recorder should not be less than 42 dB at the maximum tape speed. Note that as the dummy is articulated to sit in a vehicle or if the dummy is articulated for a test, the coordinate systems rotate with their respective dummy parts. Updated 25 Jan This method also may be used if there are no calibration methods to validate the dynamic response of the transducer type in question. The channel frequency class was Hz d.

Uploader:	Arashiramar
Date Added:	3 August 2016
File Size:	35.60 Mb
Operating Systems:	Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads:	43447
Price:	Free* [*Free Regsitration Required]

This demonstration should be undertaken on the basis of reasonable deductions from evidence in their possession, such as the results of partial tests. The amplitude response differences between the transfer functions of the two transducers should not exceed 0.

DADiSP / CFC

For CFCs of or 60, the frequency response of the channel is determined by the filter algorithm described in Appendix C. See SAE Paper In addition, recorded polarities for various transducer outputs need to be defined relative to positive directions of the appropriate coordinate systems. The dB line is defined by the calibration factor. Tom Prohaszka Tom Prohaszka view profile.

If the calibration equipment cannot produce the zae input, due to excessively high values of the quantity to be sea, calibrations shall be carried out within jj211 limits of these calibration standards and these limits shall be recorded in the report. Data Channel Performance Requirements 4.

It is assumed that the load cell of interest is contained within the cube and responds to loads applied to the surfaces of the cube.

Comments and Ratings 1. Rather, it is intended that any agency proposing to conduct tests to this document should be able to sa that if such a single test could be and were carried out, then their equipment would meet the recommendations. Bold arrows of normal forces Fshear forces Sand moments M are shown in positive directions. References are listed in Appendix A, Section A.

As such, the user must ascertain data channel and environmental compatibility j2111 establishing equivalence. Digital Data Processing— This section establishes guidelines for digital data processing equipment used by crash testing agencies.

Potential sources of transducer errors are related to data channel compatibility i. To determine the orientation of the coordinate axes, the dummy will always be considered as standing erect.

This is expressed in terms of the measured variable input. Peaks in the filtered data set will occur at the same time as peaks in the unfiltered data. However, once this decision is made then the positive directions of the y and z axes must be as indicated by corresponding orientation shown in Figure 2. The CAC number is numerically equal to the upper limit of the measurement range that is, equivalent to the data channel full scale. In this case, the coordinate system is fixed to the thoracic spine.

SAE J21 When overall acceleration of the frame or body ase a given direction is desired and a higher frequency response class is used, readability of the data may be improved by averaging outputs of two or more transducers at different locations.

DADiSP Products: Modules: CFC Full Description

In cases where properties of nonmechanical test subjects preclude rigid transducer mounting, an analytical or experimental evaluation of mounting effects on the data should be provided.

By passing the data through the filter forward and then backward the filter will not phase shift the data. The use of the reference equipment is limited to the range j211 frequencies for which they have been calibrated. Interaction of transducer characteristics can precipitate significant differences in both steady-state and transient responses between transducers with similar specifications. Tags Add Tags filter design filtering signal processing. Based on your location, we recommend that you select: Transducer mounting analysis, if required by Section 6 d.

In some systems it may be necessary to divide the whole channel into subsystems for calibration and checking purposes.

Inertia] coordinate system definition The results should be presented on A4 mm x mm size paper ISO or 8. A statistically significant number of tests should be performed to validate the results. The purpose of SAE J21 1 is to recommend "techniques of measurement used in impact tests" which "will provide a basis for zae comparison of test results from different sources.